TP-Link TL-WA5210G Manual. Typical network TL-WA5210G is used for remote point-to-point connection. It makes remote internet share possible. The typical connection for TL-WA5210G is shown as above. Please make Note sure that the two CPEs are placed face to face, otherwise the wireless signal strength might be weak. Connecting the device Note Please use only wired network connections to configure the AP. Locate a suitable mounting site for your CPE.
For choosing the best location, select an elevated location where trees, buildings and large steel structures will not obstruct the antenna signals and which offers maximum line-of-sight propagation with the users. The connection will be similar to the figure below after the above steps are finished. If you use two CPEs to build the network, please make sure that the two CPEs are placed face to face. Turn on all your network devices and then check to see if the LEDs on the AP display normally as the diagram below describes. Configuring the device You will need to assign your computer a Static IP address within the same Note range as the AP’s IP address. See the Troubleshooting T3 if you need assistance. Login Open your web browser and type in the address bar and press Enter A dialog box will prompt you for the User name and Password.
Рубрики. Инструкция по эксплуатации TP - LINK TL-WA5210G. Установка и настройка роутера TP - LINK TL-WA5210G. Прошивка TP - LINK TL-WA5210G. Плюсы: все в одном корпусе, двойная поляризация - возможность переключения через меню настроек, очень простая в настройках, удобное крепление. Поддержка стандарта IEEE 802.11b/g, скорость беспроводной передачи данных до 54 Мбит/с; Всепогодный корпус с защитой от молний (до 4000 В) и. Выгодные цены на TP - LINK TL-WA5210G в магазинах сети магазинов днс. Читайте отзывы на TP - LINK TL-WA5210G, технические характеристики и. Руководство по подключению TP - Link TL-WA5210G к точке доступа Wi-Fi. Интернет-магазин Wi-Fi оборудования ТехноТрейд.
Настройка режима Bridge (Point to Point) на точке доступа TP - Link 5210G ( похожие по прошивке модели: TP - Link TL-WA7210N, TP - LINK.
If you want to set it as a router, please choose AP Router mode, and fo r further configuration, please refer to the user guide in the resource CD; c) If you want to set up a point-to-point connection with TL-WA5210G, please skip to B;. Enter the SSID provided by your WISP Click Next Click Finish to exit the Quick Setup wizard and wait until the AP completes rebooting automatically. The changes will take effect after rebooting. Click Finish Configuration for Point-to-Point Connection Note Two TL-WA5210Gs are needed for this application. The AP Setting Select AP Click Next. Enter TP-LINK_900008, the SSID of the first AP you have configured Click Save at the bottom of this page. Configuration for Repeater To make sure the TL-WA5210G is under AP mode, please follow the steps below.
Click Operation Mode Select AP Click Save. Click Wireless > Wireless Mode Select Repeater Click Survey This page will then display.
Find the BSSID of the remote AP that you want to repeat, and then click Connect on the right side of the line. Note The BSSID is the same as the MAC address. Then click Save at the bottom of this page. RP-SMA port of your CPE directly.
2. If you don’t have any external antennas, you are recommended to use TP-LINK products for outdoor solution. You could choose TL-ANT2424B (external antenna), TL-ANT24SP (Surge Protector), and TL-ANT24PT3 (Pigtail Cable) to connect as the following steps: Connect one side of the TL-ANT24SP to the RP-SMA port of your CPE through the TL-ANT24PT3.
Login Open your web browser and type in in the address bar and press Enter A dialog box will prompt you for the User name and Password. Ente r the default values and click OK. User name: admin Password: admin Click OK Configure the external antenna Click Wireless Setting. Appendix 2: Troubleshootin g How do I restore my AP’s configuration to its factory default settings? With the AP powered on, press and hold the RESET button fo r about 8 seconds before releasing Hold it for about 8 seconds Once the AP is reset, the current configuration settings will be lost and you Note will need to reconfigure the router. Click Network Connections Right-click Local Area Connection Click Properties Double-click Internet Protocol ( TCP/IP ).
Select Use the following IP address Enter the 192. 168. 100 into the IP address field, 255. 255.
255. 0 into the Subnet mask field Select Use the following DNS server addresses Enter the DNS server address provided by your ISP or network administrator Click OK For Windows 7 OS Go to Start >.
Click Change adapter settings Right-click Local Area Connection Click Properties Double-click Internet Protocol Version 4 (TCP/IPv4). Select Use the following IP address Enter the 192. 168.
100 into the IP address field, 255. 255.
255. 0 into the Subnet mask field Select Use the following DNS server addresses Enter the DNS server address provided by your ISP or network administrator Click OK. 9:00 AM to 6:00 PM E-mail: support.
usa@tp-link. com Service time: 24hrs, 7 days a week Indonesia Tel: (+62 ) 021 6259 135 Malaysia E-mail.
support. id@tp-link. com Tel: 1300 88 875465 (1300 Service time. Monday to Friday 88TPLINK) 9:00 -12:00 ; 13:00 -18:00 Email: support.
Comments to this Manuals.